JLG TF6-42 Service Manual - Manuale (Pagina 194)

5
1.1 External interfaces overview
In the following table all references to terminals refer to the APC160 connector pins.
WIRE PIN FUNC TYPE FUNCTION
A1 A1 PPWR Pwr Permanent Battery Plus
A2 B1 VFS0+ Pwm Brake solenoid 0-1000mA
A3 C1 VFS0- Sns Brake solenoid 0-1000mA
A4 D1 VFS1+ Pwm 1/2 Solenoid out
A5 E1 VFS1- Sns n/c
A6 F1 VFS2+ Pwm 2/3 solenoid out
A7 G1 VFS2- Sns n/c
A8 H1 VFS3+ Pwm Splitter solenoid out
A9 J1 VFS3- Sns n/c
A10 K1 DO0 Stp Parking Brake solenoid out
A11 A2 ANI0 Ptg Boom Function : 0 W = Active / 3.3 kW = Inactive
A12 B2 DIGIN0 Ptp Shift lever 1-2
A13 C2 DIGIN1 Ptp Shift lever 2-3
A14 D2 DIGIN2 Ptp Shift lever H/L
A15 E2 DO1 Stp Forward solenoid out
A16 F2 DO2 Stp Reverse solenoid out
A17 G2 DIGIN3 Ptp AWP control: CABIN / AWP 12 V = Cabin Control
A18 H2 DIGIN4 Ptp Shift lever FWD
A19 J2 DIGIN5 Ptp Shift lever REV
A20 K2 DO3 Stg Parking Brake Indicator
A21 A3 GND Gnd Ground
A22 B3 SS0 Sns Output speed + (optional)
A23 C3 SS0 Gnd Output speed - (optional)
A24 D3 SS1 Sns Turbine speed sensor +
A25 E3 SS1 Gnd Turbine speed sensor -
A26 F3 SS2 Sns Engine speed sensor +
A27 G3 SS2 Gnd Engine speed sensor-
A28 H3 ANI1 Ptg Boom Pos: 3.050 W = Down & In / 1.250 W= Up or Extended
A29 J3 ANI2 Ptg Throttle position 0-5V
A30 K3 GND Gnd Signal Ground
WIRE PIN FUNC TYPE FUNCTION
B1 L1 VFS4+ HbrgA Throttle servo A 0-4A
B2 M1 ANI4 Sns Ref Voltage out 5V
B3 N1 VFS5+ HbrgB Throttle servo B 0-4A
B4 P1 ANI5 Sns Servo position feedback 0-5V
B5 R1 VFS6+ Pwm Engine Starter: ON = Disabled / OFF = Enabled
B6 S1 ANI6 Sns Center voltage of Joystick 0-5V
B7 L2 CANL Comm CANL needs external 120 W
B8 M2 CANH Comm CANH
B9 N2 RXD Comm RS232 RXD
B10 P2 TXD Comm RS232 TXD / WARNING OUT
B11 R2 SS3 Sns Parking Brake Push Button (short is active)
B12 S2 SPWR Pwr Switched Battery Plus
B13 L3 DIGIN6 Ptp Boom Speed Mode Slow / Fast 12 V = Slow
B14 M3 DIGIN7 Ptp Shift Mode: Manual / Automatic 12 V = Manual
B15 N3 DIGIN8 Ptp AWP Sensor: Disconnected / Connect 12 V = Disconnected
B16 P3 DIGIN9 Ptp Platform Enable Switch: Enable / Disable 12 V = Enable
B17 R3 ANI3 Ptg Joystick Position Sensor: 0 V =100% Rvs / 5 V =100% Fwd
B18 S3 SGND Gnd Power Ground