dB TECHNOLOGIES DSX 2040 - Manuale (Pagina 16)

E
n
g
lis
h
29
E
n
g
lis
h
30
7.6 SECURITY PASSWORD
The factory default password is blank ("____"), it can be changed to any combination of 4
characters in this menu.
OLD PW:
The user is required to enter the old password first to modify the password.
NEW PW:
The new password desired.
SYSTEM Passwd
OLD PW : ____
SYSTEM Passwd
NEW PW : ____
8.0 QUICK REFERENCE
Parameters Menu<<Menu>> Field<<Cursor>> Min Max Steps Units
Level Signal LEVEL -40 +15 0.25 dB
Polarity Signal POL + / -
Delay Signal DELAY 0 62400 1 10us steps
EQ Number EQ EQ# 1 8 1
EQ Bypass EQ BYPASS Off /On
EQ Type EQ TYPE PEQ / Lo-Shf / Hi-Shf / AP-1 / AP-2
EQ Level EQ LEVEL -30 +15 0.25 dB
EQ Frequency EQ FREQ 20 30.000 1 Hz
EQ Bandwidth EQ BW 0.02 3.61 0.01 Octave
GEQ Number GEQ GEQ# 1 31 1
GEQ Level GEQ LEVEL -30 +15 0.25 dB
GEQ Bypass GEQ BYPASS Off / On
XOver Low Type Xover FTRL Off / Butterworth / Linkwitz-Riley / Bessel
XOver Low Frequency Xover FRQL 20 30.000 1 Hz
XOver Low Slope Xover SLPL 6 48 6 dB/octave
XOver High Type Xover FTRH Off / Butterworth / Linkwitz-Riley / Bessel
XOver High Frequency Xover FRQH 20 30.000 1 Hz
XOver High Slope XOver SLPH 6 48 6 dB/octave
Compressor Threshold Comp THRESH -20 +20 0.5 dBu
Compressor Attack Time Comp ATTACK 0.3 100 0.1 / 1 ms
Compressor Release Time Comp RELEASE 2 / 4 / 8 / 16 / 32X Attack time
Compressor Ratio Comp RATIO 1:1 to 1:40
Limiter Threshold Limit THRESH -20 +20 0.5 dBu
Limiter Attack Time Limit ATTACK 0.3 100 0.1/1 ms
Limiter Release Time Limit RELEASE 2 / 4 / 8 / 16 / 32X Attack time
Source Source 1, 2, 3, 4, 5, 6, 7, 8 Off +15 0.25 dB
Channel Name Name NAME 6 characters
SYSTEM Secure
PASSWORD: ____
7.7 SECURITY LOCK
The DSX 2040 enables the user to secure the unit and prevent undesired changes in the
setup. In order to lock or unlock the unit the user must enter the correct password. The user
can only lock or unlock all menus using the front panel, XConsole is required to lock or
unlock individual menu.
PASSWORD:
The password is 4 characters in length. The factory default of a new unit does not require a
password. The user can change the password via XConsole or the Set Password menu.
9.0 PC CONTROL SOFTWARE
The DSX 2040 is shipped with a special PC Graphic User Interface (GUI) application -
XConsole. XConsole gives the user an option to control the unit from a remote PC via the
serial communication link. The GUI application makes it much easier to control and monitor
the device, allowing the user to get the whole picture on one screen. Programs can be
recalled and stored from/to PC's hard drive, thus expanding the storage to become virtually
limitless.
XConsole can be connected to the DSX series via RS232 or USB. USB requires the
installation of additional driver. The user is given an option to install it during the installation
of XConsole, and if the user did not install it at that time, they may choose to do so by
running the USB driver installer from the provided software CD or last download from
www.dbtechnologies.com.